Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
    3.1. Petrol engines
    3.2. Diesel engines
      3.2.1. A technical characteristics
       3.2.2. Engine adjustments
      3.2.3. Removal and installation of the fuel pump of a high pressure
      3.2.4. Installation of the fuel pump of high pressure BOSCH
      3.2.5. Installation of the fuel pump of high pressure Roto Diesel
      3.2.6. Removal of water from the fuel filter
      3.2.7. Removal of air from fuel system
      3.2.8. Removal and atomizer installation
      3.2.9. Check электрически the operated valve of a stop of the engine
      3.2.10. Pump Bosch adjustment
      3.2.11. Pump Roto Diesel adjustment
      3.2.12. Removal and installation турбокомпрессора
       3.2.13. The repair which is not demanding removal of the engine
         3.2.13.1. Removal of a gear belt of a drive of a camshaft
         3.2.13.2. Installation of a gear belt of a drive of a camshaft
         3.2.13.3. Removal of a head of the block of cylinders
         3.2.13.4. Installation of a head of the block of cylinders
         3.2.13.5. Repair of a head of the block of cylinders
      3.2.14. Engine removal
      3.2.15. Engine installation
      3.2.16. Engine dismantling
      3.2.17. Engine assemblage
      3.2.18. The oil pump
       3.2.19. Cooling system
      3.2.20. System of release of the fulfilled gases
    3.3. The petrol engine 1,4 дм3
    3.4. Ignition system
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment


3.2.13.3. Removal of a head of the block of cylinders
THE GENERAL DATA

This operation demands partial removal of a gear belt.

PERFORMANCE ORDER
1. Fix the right top support of the engine, and then take the adaptation of support of the engine (it does not concern engine XUD 7ТЕ).
2. Remove the air filter, and also its connections, pipelines of injection and a cover of a head of the block of cylinders.
3. Disconnect from a head of the block of cylinders branch pipes of a cooling liquid, fuel pipelines, electric connections. Disconnect the draught of idling strengthened on the pump with the increased number of turns.
4. In engine XUD 7ТЕ incline the engine forward and insert wooden брусок (fig. Placing wooden бруска for engine fixing see). Remove an inlet collector (the central screw of fastening).
5. Remove a belt of a drive of the pump of the amplifier of a steering (if the car is equipped by a steering with the amplifier).
6. Remove the left eye for engine lifting.
7. In engine XUD 9 disconnect a final tube about a collector and take it from a broad tank.
8. Unscrew a bolt of fastening of a pulley to a camshaft, unscrew blocking bolt and remove a gear pulley.
9. Screw up a nut of an axis of a tension roller and unscrew the top bolt.
10. Unscrew a bolt of fastening of an arm of the engine to a head of the block of cylinders.
11. In engine XUD 7ТЕ unscrew three bolts of fastening турбокомпрессора to a final collector.
12. Unscrew ten bolts of fastening of a head of the block of cylinders "on a spiral", beginning from an external bolt, and take them together with washers.
13. Separate a head of the block of cylinders and remove, directing it on the right party so that to take the end of a camshaft from an aperture of the case of a camshaft. Скобу fastenings of a bypass branch pipe (on the right party of the engine) should be protected rags in order to avoid damage of a surface of connection during removal of a head of the block of cylinders.