Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
   13.1. Care of a body
   13.2. Care of an upholstery and rugs
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   13.5. A forward bumper
   13.6. A back bumper
   13.7. Replacement of a headlight and the index of turns
   13.8. Replacement of a back lantern
   13.9. Replacement of a forward wing
   13.10. A cowl
   13.11. A cable of the lock of a cowl
   13.12. The cowl lock
   13.13. Replacement of the forward panel
   13.14. Doors
   13.15. A door upholstery
   13.16. The lock and handles of opening of a door
   13.17. Glasses of doors
   13.18. A luggage carrier cover (models the Sedan)
   13.19. The lock of a cover of a luggage carrier (model the Sedan)
   13.20. A back door (model of Kombi)
   13.21. The lock of a back door (model of Kombi)
   13.22. The central blocking
   13.23. Electric window raiser
   13.24. External rear-view mirrors
   13.25. Front and back has flown down
   13.26. The hatch
   13.27. Demountable elements of a body
   13.28. Seats
   13.29. Seat belts
   13.30. Salon furnish
   13.31. A ceiling upholstery
   13.32. The central console
   13.33. The panel of devices
14. An electric equipment


create courses with AI

13.15. A door upholstery
THE GENERAL DATA
The prevention

The door upholstery can have changes depending on level of furnish of salon. Therefore process of removal of an upholstery can differ from the stated.

The actions connected with removal of an upholstery of forward and back doors, are identical.

Removal

PERFORMANCE ORDER
1. To lower door glass more than half.
2. By means of a screw-driver (for extraction of a special ledge) to remove an overlay of the door handle.
3. In the cars equipped with built in loudspeakers to unscrew screws of a lattice dynamics or to remove brackets fastenings, to disconnect, and then to take a loudspeaker.
4. To remove the button of draught of blocking of doors for what to pull it upwards, simultaneously a screw-driver wringing out a clamp.
5. On models with manual стеклоподъемником to remove its handle about axes and a lining.
6. In versions with электрически lifted glasses to disconnect the accumulator, then by means of a screw-driver to take the switch from a door and to disconnect a socket.
7. To remove a decorative overlay of an external mirror.
8. To unscrew three screws of fastening of an armrest and to remove an armrest.
9. On later models by means of the lever to remove a plate of furnish from a back part of a pocket of a door and to unscrew the screw of fastening of a back part of an upholstery of doors.
10. Where it is applicable, using a screw-driver, to disconnect brackets the fastenings of an upholstery located in a nest for a loudspeaker.
11. By means of the flat special adaptation in the form of plugs to unhook an upholstery of a door so that not to damage plastic latches. In case of damage of latches it is not necessary to stick together them, and to establish in internal strengthening of an upholstery of a door.
12. To raise an upholstery and to remove it from a door.

Installation

PERFORMANCE ORDER
1. On apertures of a skeleton of a door to paste a plastic tape to protect from коррозиии and that water did not get in salon.
2. All latches to establish in corresponding apertures of a door and to fix a door upholstery.
3. To establish the button of draught of blocking of doors for what to arrange draught in lower of two apertures, strongly to pull the button over draught before fixing, thus draught of fastening will appear in the top aperture.
4. Other actions to execute in return sequence in relation to upholstery removal.
5. During movement to check up, whether there is a vibration of an upholstery of a door.
The prevention

For protection of doors from corrosion and also to achieve a deaf sound at their closing, it is necessary to fill in special bitumen means in an internal cavity of a door. It can be made only when a skeleton of a door ideally dry (without the slightest traces of a moisture).