1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
   13.1. Care of a body
   13.2. Care of an upholstery and rugs
   13.3. Repair of insignificant damages of a body
   13.4. Repair of strong damages of a body
   13.5. A forward bumper
   13.6. A back bumper
   13.7. Replacement of a headlight and the index of turns
   13.8. Replacement of a back lantern
   13.9. Replacement of a forward wing
   13.10. A cowl
   13.11. A cable of the lock of a cowl
   13.12. The cowl lock
   13.13. Replacement of the forward panel
   13.14. Doors
   13.15. A door upholstery
   13.16. The lock and handles of opening of a door
   13.17. Glasses of doors
   13.18. A luggage carrier cover (models the Sedan)
   13.19. The lock of a cover of a luggage carrier (model the Sedan)
   13.20. A back door (model of Kombi)
   13.21. The lock of a back door (model of Kombi)
   13.22. The central blocking
   13.23. Electric window raiser
   13.24. External rear-view mirrors
   13.25. Front and back has flown down
   13.26. The hatch
   13.27. Demountable elements of a body
   13.28. Seats
   13.29. Seat belts
   13.30. Salon furnish
   13.31. A ceiling upholstery
   13.32. The central console
   13.33. The panel of devices
14. An electric equipment

13.10. A cowl

Cowl knot

1 – the hinge of a cowl,

2 – a cowl,

3 – a sealant,

4 – a separating sealant,

5 – a clip of an emphasis,

6 – an emphasis


1. To open a cowl. A paint to designate position of hinges of a cowl concerning two elements of fastening.
2. To unscrew a bolt of fastening of the tyre of grounding to a cowl.
3. To weaken two bolts of fastening of each hinge to a cowl.
4. To establish the holder of a brush so that to keep a cowl the opened.
5. To unscrew four screws of fastening of a cowl to hinges (on two from each party).
6. To unscrew bolts (A) fastenings of loops to a cowl and bolts (B) fastenings of loops to a body.
7. To remove a cowl. Not to damage the varnished surface of forward wings, cowl removal should be made together.


During works on a cowl it is not necessary to impose too a considerable quantity of polyester pitch because it tends to растрескиванию at sharp closings or at fluctuations.

1. Before a covering of a cowl a varnish it is necessary to put sealing weight on connections of internal amplifiers of a cowl.
2. For avoidance of corrosion and noise reduction it is necessary to spray special anticorrosive means on a cowl inside.
3. Before performance of the subsequent actions the cowl should dry within one night at temperature 20 ° With.
4. In the closed profiles (in cowl amplifiers) it is necessary to inject a special wax liquid into aerosols.


1. To grease bolts of hinges.
2. To establish a cowl on hinges, without screwing up definitively connections. Two persons should carry out this action.
3. To establish on corresponding places and to screw up cowl hinges.
4. To adjust a backlash between a cowl and wings, and also between a cowl and a radiator lattice.
5. For this purpose it is necessary to execute following actions. To adjust elements of fastening of a cowl its position in a horizontal plane.
6. To adjust elements of lateral fastening position of hinges in a vertical plane.
7. To be convinced that the cowl opens normally.
8. Definitively to screw up elements of fastening of hinges.
9. To close a cowl and to be convinced of its normal opening and closing.