Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
   12.1. A technical characteristics
   12.2. Prorolling of hydraulic brake system
   12.3. Replacement of lobbies brake pads
   12.4. Brake pipelines and hoses
   12.5. Replacement back brake pads on disk brakes
   12.6. Replacement back brake pads on drum-type brakes
   12.7. A forward brake disk
   12.8. A back brake disk
   12.9. A back brake drum
   12.10. A support of a forward brake
   12.11. A support of a back wheel
   12.12. The back brake cylinder
   12.13. The main brake cylinder
   12.14. A brake pedal
   12.15. The vacuum amplifier of brakes
   12.16. The unilateral valve of the vacuum amplifier of brakes
   12.17. Adjustment of a manual brake
   12.18. The lever of a manual brake
   12.19. A cable of a manual brake
   12.20. The switch of a control lamp of inclusion of a manual brake
   12.21. The valve of adjustment of pressure in brake system
   12.22. The stoplight switch
   12.23. Antiblocking system (ABS)
   12.24. Replacement of the gauge of a wheel
   12.25. Removal of air from brake system
13. A body
14. An electric equipment


Источник: https://welx.net

12.5. Replacement back brake pads on disk brakes
THE GENERAL DATA
The prevention

Necessarily make replacement of all pads on one axis of the car even if deterioration borders were reached by one колодка.

At installation brake pads it is necessary to use a new top bolt of fastening of a directing finger.

PERFORMANCE ORDER
1. To lift a back part of the car and to fix on supports.
2. To remove back wheels.
3. To disconnect a cable of a manual brake from a control lever on a support.
4. To unscrew the top bolt of fastening of the bottom directing finger. Thus for deduction of a directing finger from проворачивания to use a thin wrench. For fastening of a directing finger to use only a new bolt.
5. To turn a support downwards on a directing finger, thus to watch a tension of a brake hose.
6. To take brake pads from a support.
7. To measure a thickness of an overlay of everyone brake pads.
8. If pads are suitable to the further operation, to clear them, using a wire brush and rags.
9. Before installation pads to check up that directing plugs easily move in a support and rubber protective covers are not damaged.
10. If will be established new brake pads, using the special tool, to press the piston into a support, simultaneously turning it clockwise.
11. To turn the piston so that grooves in the piston were established on the support centre.
12. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly to observe of liquid level in a tank and if necessary to pump out it.
13. At installation old brake pads to put them on the former places.
14. To insert brake pads in the holder of a support.
15. To establish a support on brake pads.
16. To grease a carving of a bolt of fastening of a directing finger with means against unscrewing (Peugeot recommends Loctite Frenetanch).
17. To press a support that it has occupied the position, then to screw up a bolt of fastening of a directing finger, tightening its demanded moment.
18. To connect a cable of a manual brake to a support.
19. Some times to press a brake pedal that pads have nestled on a disk and repeatedly to check up level of a brake liquid in a tank.
20. To execute the same actions on the second back wheel.
21. To establish wheels and to lower the car.
22. Repeatedly to check up level of a brake liquid.