Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
   12.1. A technical characteristics
   12.2. Prorolling of hydraulic brake system
   12.3. Replacement of lobbies brake pads
   12.4. Brake pipelines and hoses
   12.5. Replacement back brake pads on disk brakes
   12.6. Replacement back brake pads on drum-type brakes
   12.7. A forward brake disk
   12.8. A back brake disk
   12.9. A back brake drum
   12.10. A support of a forward brake
   12.11. A support of a back wheel
   12.12. The back brake cylinder
   12.13. The main brake cylinder
   12.14. A brake pedal
   12.15. The vacuum amplifier of brakes
   12.16. The unilateral valve of the vacuum amplifier of brakes
   12.17. Adjustment of a manual brake
   12.18. The lever of a manual brake
   12.19. A cable of a manual brake
   12.20. The switch of a control lamp of inclusion of a manual brake
   12.21. The valve of adjustment of pressure in brake system
   12.22. The stoplight switch
   12.23. Antiblocking system (ABS)
   12.24. Replacement of the gauge of a wheel
   12.25. Removal of air from brake system
13. A body
14. An electric equipment


12.19. A cable of a manual brake
THE GENERAL DATA

Elements of a manual brake

1 – the lever manual
Brakes,

2 – the switch of a stoplight,

3 – a forward cable,

4 – back cables

The cable of a manual brake consists of 3 parts: a forward part which includes the adjustment mechanism, the right and left back parts which connect back brakes to the adjustment mechanism on a forward cable. Each part can be removed separately.

FORWARD CABLE OF THE MANUAL BRAKE

Removal and installation

PERFORMANCE ORDER
1. To lift a back part of the car and to fix on supports.
2. Under the car to remove an intermediate link of an exhaust system and a heat resisting guard.
3. To weaken a counternut, to unscrew a regulator nut, as much as possible to weaken a cable of a manual brake.
4. To release brackets fastenings of a forward cable under the car, then to disconnect a cable from the right cable in a connector of cables and from a regulator suspension bracket.
5. Working under the lever of a manual brake, to disconnect a cable from a plate of installation of the lever.
6. On models with the usual central console to tighten the lever of a manual brake, and to remove furnish of a manual brake from the top part of the central console.
7. To remove furnish on the lever of a manual brake.
8. On models with the improved central console to remove the central console.
9. To lift the lever of a manual brake before the fifth click, for access by the cable end.
10. To advance a cable forward and to remove from a ledge on the lever.
11. To extend a cable downwards through a plate of installation of the lever, and to take it from under the car.
12. Installation is made in sequence of return to removal.
13. To check up and if necessary to adjust work of a manual brake.

BACK CABLE OF THE MANUAL BRAKE ON DRUM-TYPE BRAKES

Removal and installation

PERFORMANCE ORDER
1. To lift a back part of the car and to fix on supports.
2. Under the car to remove an intermediate link of an exhaust system and a heat resisting guard.
3. To weaken a counternut on the mechanism of a regulator and to unscrew a regulator nut.
4. At removal of the left cable to unscrew a nut of a regulator from the end of the carving plug, and to disconnect the end of a cable from a regulator suspension bracket.
5. At removal of the right cable to disconnect the right cable from a cable in a connector of cables.
6. To remove a corresponding brake drum.
7. Using flat-nose pliers, to disconnect the end of a cable of a manual brake from a control lever on brake колодке.
8. To take a cover of a cable from a brake board.
9. To release on all length a cable from скоб fastenings and to remove from under the car.
10. Installation is made in sequence of return to removal.
11. To check up and if necessary to adjust work of a manual brake.

BACK CABLE OF THE MANUAL BRAKE ON DISK BRAKES

PERFORMANCE ORDER
1. To lift a back part of the car and to fix on supports.
2. Under the car to remove an intermediate link of an exhaust system and a heat resisting guard.
3. To weaken a counternut on the mechanism of a regulator and to unscrew a regulator nut.
4. At removal of the left cable to unscrew a nut of a regulator from the end of the carving plug, and to disconnect the end of a cable from a regulator suspension bracket.
5. At removal of the right cable to disconnect the right cable from a cable in a connector of cables.
6. To disconnect a cable from a control lever on a support, then to disconnect a cover of a cable from a support suspension bracket.
7. To release on all length a cable from скоб fastenings and to remove from under the car.
8. Installation is made in sequence of return to removal.
9. To check up and if necessary to adjust work of a manual brake.