| 1. To lift a forward part of the car and to fix on supports. |
| 2. To remove forward wheels. |
|
3. To disconnect the electric socket located on a wire, going to the gauge of deterioration brake pads. |
| 4. To press the piston into a support, displacing a support aside, opposite piston arrangements. |
| Support Bendix |
The prevention At installation pads it is necessary to use a new collar of fixing of a plate of fastening brake pads.
|
|
5. Using flat-nose pliers, to remove a small collar of fixing of a plate of fastening brake pads. |
|
6. To take a fastening plate pads from a support. |
|
7. To take brake pads from a support, marking an arrangement of a spring of antijingle and to remove a spring with pads. |
|
8. To measure a thickness of an overlay of everyone brake pads. |
| 9. If the condition of overlays brake pads allows their further operation, to clear them, using a pure wire brush and rags. |
| 10. Before installation pads to check up, that directing fingers freely moved in the holder of a support and to check up that rubber protective covers of a directing finger are not damaged. |
| 11. To clear a dust and a dirt from a support and the piston. |
| 12. To check up a condition of dustproof consolidation round the piston. |
| 13. If will be established new brake pads, to press the piston into a support. It can be made a wooden core or the hammer handle. Thus especially to watch, that the piston has not warped also surfaces of the piston and duster have not been damaged. |
| 14. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly to observe of liquid level in a tank and if necessary to pump out it. |
| 15. At installation old brake pads to put them on the former places. |
|
16. To establish a spring preventing a tinkling sound brake pads. |
| 17. To establish brake pads in a support. |
|
18. At correct installation brake pads if to look on pads from a forward part of the car, the flute on internal колодке should be above, than a flute on external колодке (B – flutes on brake колодках, D – a spring collar, V – the prorolling union). |
| 19. To establish a plate of fixing brake pads and to fix its spring collar. |
| 20. To connect a socket of the gauge of deterioration brake pads. |
| 21. To check up level of a brake liquid in a tank. It should not exceed a mark "max". |
| 22. Some times to press a brake pedal that pads have nestled on a disk and repeatedly to check up level of a brake liquid in a tank. |
| 23. To execute the same actions on the second forward wheel. |
| 24. To establish wheels and to lower the car. |
| 25. Repeatedly to check up level of a brake liquid. |
| Support Girling |
The prevention At installation brake pads it is necessary to use a new bolt of fastening of a directing finger.
|
|
26. To unscrew a bolt of fastening of the bottom directing finger. Thus for deduction of a directing finger from проворачивания to use a thin wrench. For fastening of a directing finger to use only a new bolt. |
|
27. To turn a support upwards on the top directing finger and to tie up to a rack by means of a soft wire. |
| 28. To take brake pads from the holder of a support. |
| 29. To measure a thickness of an overlay of everyone brake pads. |
| 30. If the condition of overlays brake pads allows their further operation, to clear them, using a pure wire brush and rags. |
| 31. Before installation pads to check up, that directing fingers freely moved in the holder of a support and to check up that rubber protective covers of a directing finger are not damaged. |
| 32. To clear a dust and a dirt from a support and the piston. |
| 33. To check up a condition of dustproof consolidation round the piston. |
| 34. If will be established new brake pads, to press the piston into a support. It can be made a wooden core or the hammer handle. Thus especially to watch, that the piston has not warped also surfaces of the piston and duster have not been damaged. |
| 35. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly to observe of liquid level in a tank and if necessary to pump out it. |
| 36. At installation old brake pads to put them on the former places. |
|
37. To insert external and internal brake pads in the holder of a support. |
|
38. To lower a support on brake pads, passing a wire from the gauge of deterioration brake pads through a window in a support. |
| 39. To grease a carving of a bolt of fastening of a directing finger with means against unscrewing (Peugeot recommends Loctite Frenetanch). |
| 40. To press a support that it has occupied the position, then to screw up a bolt of fastening of a directing finger, tightening its demanded moment. |
| 41. To connect an electric socket of the gauge of deterioration brake pads. |
| 42. To check up level of a brake liquid in a tank. It should not exceed a mark "max". |
| 43. Some times to press a brake pedal that pads have nestled on a disk and repeatedly to check up level of a brake liquid in a tank. |
| 44. To execute the same actions on the second forward wheel. |
| 45. To establish wheels and to lower the car. |
| 46. Repeatedly to check up level of a brake liquid. |