8.1.7. Sealing rings

THE GENERAL DATA

SEALING RINGS OF POWER SHAFTS

Use of the plastic protective plug at installation of a sealing ring of a power shaft

PERFORMANCE ORDER

1. To establish a forward part of the car on supports and to remove a wheel from the corresponding party. 2. To remove the bottom casing (equipment in some versions). 3. To merge oil from a transmission. 4. To unscrew a nut of fastening of the bottom spherical hinge and to disconnect a fixing element of a nave from the bottom lever, using a special stripper. The right sealing ring of a power shaft 5. To weaken two nuts of fastening of the intermediate bearing and to turn on a half-turn fastening bolts so that to take them эксцентриковые heads from the bearing case. 6. To pull a nave for limits of the car for extraction of the internal end of a power shaft and clearing of the intermediate bearing from an installation suspension bracket. 7. After extraction of a power shaft from a transmission to shift a dustproof cover from the internal end of a shaft, marking its arrangement, and using a soft wire to suspend a shaft to a body. 8. Being careful, by means of a screw-driver used as the lever, to take a sealing ring from a transmission. 9. To clear a nest for a sealing ring, to oil working edges of a new sealing ring and using tubular the mandrel to establish a sealing ring in a nest in a transmission. If the sealing ring is supplied by the plastic protective plug, she is necessary for establishing before power shaft installation. 10. Completely to clear Slots a power shaft, then to apply a thin film lubricant on working edges of a sealing ring and on Slots on the internal end of a power shaft. 11. To establish a dustproof cover on the shaft end so that the flat surface has been directed to a transmission. 12. To combine Slots a power shaft with шлицами a semiaxial gear wheel of differential, then to level the intermediate bearing with an installation suspension bracket, and to establish a power shaft in a transmission. 13. To check up that the intermediate bearing is correctly established, then to turn fastening bolts back on 90 ° so that their heads were established opposite to an external ring of the bearing, and to tighten nuts of fastening by the demanded moment. To remove a plastic protective ring. 14. To connect a pin spherical swivel connections with the bottom lever. 15. To establish a wheel, then to lower the car and definitively to tighten bolts of fastening of a wheel. 16. To fill in in a transmission oil. The left sealing ring of a power shaft 17. To pull a nave for limits of the car for extraction of the internal end of a power shaft from a transmission. 18. Being careful, by means of a screw-driver used as the lever, to take a sealing ring from a transmission. 19. To clear a nest for a sealing ring, to oil working edges of a new sealing ring and using tubular the mandrel, to establish a sealing ring in a nest in a transmission. 20. Completely to clear Slots a power shaft, then to apply a thin film lubricant on working edges of a sealing ring and on Slots on the internal end of a power shaft. 21. To combine Slots a power shaft with шлицами a semiaxial gear wheel of differential and to establish a power shaft in a transmission. 22. To connect a pin spherical swivel connections with the bottom lever. 23. To establish a wheel, then to lower the car and definitively to tighten bolts of fastening of a wheel. 24. To fill in oil in a transmission.

SEALING RING OF THE ENTRANCE SHAFT

PERFORMANCE ORDER

1. To remove a transmission. 2. To unscrew three bolts, крепящие directing plug of the bearing of deenergizing of coupling and to shift directing plug from an entrance shaft, together with a sealing ring of round section. 3. Being careful, by means of a screw-driver used as the lever, to take a sealing ring from the directing plug. 4. To check up a condition of a surface of an entrance shaft of a transmission interfaced to a sealing ring and in the presence of scratches or задиров to polish this surface or to replace an entrance shaft. 5. To lower a new sealing ring in oil and to establish on directing plug выжимного the bearing. 6. To establish a new sealing ring of round section on a back part of the directing plug. 7. To establish directing plug into place, pulling it over an entrance shaft. 8. To screw bolts of fastening of the directing plug, having tightened their demanded moment. 9. To establish a transmission.

SEALING RING OF THE SHAFT OF THE CHOICE OF TRANSFERS

PERFORMANCE ORDER

1. To lift a forward part of the car and to fix on supports. To remove the left forward wheel. 2. Using a screw-driver as the lever, to remove spherical шарнирное connection of draught from a shaft of a choice of transfers. 3. Using a screw-driver as the lever, to take a sealing ring of a shaft of a choice of transfers from a casing (drawing at the left) and to shift it from the shaft end (drawing on the right). 4. To check up a condition of a surface of a shaft of a choice of transfers interfaced to a sealing ring and in the presence of scratches or задиров to polish this surface or to replace a shaft of a choice of transfers. 5. To grease working edges of a new sealing ring and pulling over a shaft of a choice of transfers to establish a sealing ring into place in a transmission. 6. To connect draught to shaft of a choice of transfers. To establish the left forward wheel and to lower the car.