Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
    3.1. Petrol engines
    3.2. Diesel engines
    3.3. The petrol engine 1,4 дм3
      3.3.1. A technical characteristics
      3.3.2. Check and adjustment of a backlash of valves
      3.3.3. Check and adjustment of a corner of an advancing of ignition
      3.3.4. Carburettor adjustment
      3.3.5. Removal of the air filter
      3.3.6. Removal of a head of the block of cylinders
      3.3.7. Installation of a head of the block of cylinders
      3.3.8. Removal and installation of the power unit from the petrol engine 1,4 дм3
      3.3.9. Features of dismantling of the petrol engine 1,4 дм3
      3.3.10. Engine TU3 dismantling
      3.3.11. Dismantling of a head of the block of cylinders
      3.3.12. Assemblage of a head of the block of cylinders
      3.3.13. Definition of the size of loose leaves
      3.3.14. Engine TU3 assemblage
      3.3.15. Removal of the oil pump
      3.3.16. Dismantling of the oil pump
      3.3.17. Removal of the pump of a cooling liquid
      3.3.18. Service and repair of a transmission of type МА
      3.3.19. Removal and installation of a transmission of type МА
      3.3.20. Transmission dismantling
      3.3.21. Dismantling of a secondary shaft
      3.3.22. Dismantling of a primary shaft
      3.3.23. Differential dismantling
      3.3.24. Dismantling of knot of plugs with their axes
      3.3.25. Dismantling of the plug of synchronizers
      3.3.26. Verification of parts of a transmission
      3.3.27. Assemblage of the plug of synchronizers
      3.3.28. Assemblage of knot of plugs with their axes
      3.3.29. Differential assemblage
      3.3.30. Assemblage of a primary shaft
      3.3.31. Assemblage of a secondary shaft
      3.3.32. Transmission assemblage
    3.4. Ignition system
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment


3.3.32. Transmission assemblage
PERFORMANCE ORDER
1. To establish in an average part картера transmissions an external ring of the left bearing of differential.
2. To grease bolts of fastening of the directing plug выжимного the bearing герметизирующим with means "Loctite Frenetanch", sealant edges – greasing. To insert directing plug выжимного the bearing together with a new lining into a forward part картера (картер couplings) and to screw its bolts.
3. To establish in a forward part картера transmissions an external ring of the right bearing of differential.
4. To establish in a forward part картера four plugs, bearings aligning an intermediate plate.
5. To establish knot of the lever of a choice of transfers in a forward part картера, having inserted the internal lever together with an axis of knot of the lever inside картера, a lining and the external lever outside картера then to fix lever knot pinом, connecting an axis with the external lever of a choice of transfers.
6. Into a forward part картера transmissions to insert differential, pin and a spring of blocking of a reverse gear.
7. A surface of connection of an intermediate plate of bearings with a surface of a forward part картера transmissions to grease with glue "Loctite Scelmetal".
8. To establish an intermediate plate of bearings on a surface of a forward part картера transmissions, to grease bolts of fastening of an intermediate payment silicone герметизирующим with means "Loctite Frenetanch", to tighten bolts the moment of 50 Nanometers and to clean surpluses of glue.
9. Knots of gear wheels together with both shaft to put to knot of plugs with their axes and to insert in картер transmissions.
10. To insert the selector into a holder, and then to establish a holder so that simultaneously a selector finger has entered into cuts of plugs, and the holder was hooked by teeths with the internal lever of a choice of transfers.
11. To compress a spring of an axis of the selector with its two washers and to insert outside between a holder of the selector and a nave of an axis of the selector of an intermediate plate.
12. A selector axis to put on a lining and to insert outside a selector axis consistently into apertures: an external nave of an axis of the selector of an intermediate plate, a spring with plates, holders of the selector with the selector and an internal nave of an axis of the selector of an intermediate plate. To establish pin selector fastenings on its axis.
13. To insert plugs of a reverse gear and to press an axis of plugs of a reverse gear against the stop.
14. To insert a reverse gear gear wheel into cut of plugs of a reverse gear, an axis of a gear wheel of a reverse gear and the plug.
15. To degrease a surface of connection of forward and average parts картера transmissions and to grease with its thin layer silicone герметизирующего means (for example, "Framet Autojoint").
16. To establish an average part картера on a lobby and to tighten bolts of fastening by the moment of 17,5 Nanometers.
17. To establish two plates fixing the bearing of a secondary shaft, having screwed up on two screws of fastening.
18. On the end of a primary shaft to establish a gear wheel of 5th transfer (without propping up картер a transmission), and also to establish a spring lining and a sealing ring.
19. On secondary to a shaft to establish a gear wheel of 5th transfer together with a racetrack, the needle bearing and a basic lining.
20. On the end of a secondary shaft to establish synchronizer knot (a nave-sliding the plug) 5th transfer together with plugs.
21. To include 5th transfer, having moved the synchronizer plug, and still any other transfer for fixation of shaft of a transmission.
22. To tighten a nut with a washer on the end of a secondary shaft the moment of 137,5 Nanometers.
23. To switch a transmission in neutral position (to switch off transfers).
24. To hammer pin fastenings of 5th transfer.
25. To establish a back cover картера, having tightened bolts the moment of 17,5 Nanometers.
26. To establish driving the speedometer platen, having screwed a bolt of its fastening to картеру transmissions.
27. In a forward part of a transmission to establish выжимной the coupling bearing.

28. To establish sealing rings of semiaxes in картер transmissions. Before installation of semiaxes it is necessary to cover sealing edges of rings with greasing.