Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
    3.1. Petrol engines
    3.2. Diesel engines
    3.3. The petrol engine 1,4 дм3
      3.3.1. A technical characteristics
      3.3.2. Check and adjustment of a backlash of valves
      3.3.3. Check and adjustment of a corner of an advancing of ignition
      3.3.4. Carburettor adjustment
      3.3.5. Removal of the air filter
      3.3.6. Removal of a head of the block of cylinders
      3.3.7. Installation of a head of the block of cylinders
      3.3.8. Removal and installation of the power unit from the petrol engine 1,4 дм3
      3.3.9. Features of dismantling of the petrol engine 1,4 дм3
      3.3.10. Engine TU3 dismantling
      3.3.11. Dismantling of a head of the block of cylinders
      3.3.12. Assemblage of a head of the block of cylinders
      3.3.13. Definition of the size of loose leaves
      3.3.14. Engine TU3 assemblage
      3.3.15. Removal of the oil pump
      3.3.16. Dismantling of the oil pump
      3.3.17. Removal of the pump of a cooling liquid
      3.3.18. Service and repair of a transmission of type МА
      3.3.19. Removal and installation of a transmission of type МА
      3.3.20. Transmission dismantling
      3.3.21. Dismantling of a secondary shaft
      3.3.22. Dismantling of a primary shaft
      3.3.23. Differential dismantling
      3.3.24. Dismantling of knot of plugs with their axes
      3.3.25. Dismantling of the plug of synchronizers
      3.3.26. Verification of parts of a transmission
      3.3.27. Assemblage of the plug of synchronizers
      3.3.28. Assemblage of knot of plugs with their axes
      3.3.29. Differential assemblage
      3.3.30. Assemblage of a primary shaft
      3.3.31. Assemblage of a secondary shaft
      3.3.32. Transmission assemblage
    3.4. Ignition system
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment


3.3.12. Assemblage of a head of the block of cylinders
PERFORMANCE ORDER
1. Before assemblage it is necessary to clear all details and to check up their condition.
2. To degrease all details of a head of the block of cylinders.
3. To grease with engine oil cores of valves, and then to insert valves into the corresponding directing.
4. To insert the bottom cups of springs of valves.
5. New маслоотражательные caps to put on cores of valves, to grease with their engine oil and to press caps on directing valves.
6. To insert springs of valves and the top cups of springs.
7. To compress by turns each spring of the valve by means of the corresponding adaptation and to insert crackers. After adaptation removal to check up correctness of installation of crackers of each spring of the valve.
8. To grease with engine oil of a nest of bearings of a camshaft in a head of the block of cylinders.
9. To insert a camshaft into nests of a head of the block of cylinders.
10. To insert a sealing ring of a camshaft by means of special adaptation Peugeot (the adaptation 0132Т), and also a plate holding a camshaft and to tighten a bolt of a plate the moment of 15 Nanometers.
11. To establish inlet and final collectors.
12. To screw the case of the thermostat and to establish the thermostat.
13. To screw in in a head of the block of cylinders of a spark plug the moment of 17,5 Nanometers.
14. To establish an arm of the distributor of ignition.
15. To establish the ignition coil, the fuel pump and the ignition distributor.