Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
    3.1. Petrol engines
      3.1.1. A technical characteristics
       3.1.2. Engine repair
          3.1.2.1. The repair which is not demanding removal of the engine
            3.1.2.1.1. Compression check
            3.1.2.1.2. Check and adjustment of a backlash of valves
            3.1.2.1.3. A privodnoj belt of a camshaft
            3.1.2.1.4. Pulleys of a gear belt
            3.1.2.1.5. Replacement of consolidation of a camshaft
            3.1.2.1.6. Replacement of consolidations of a cranked shaft
            3.1.2.1.7. A privodnoj belt of the generator
            3.1.2.1.8. The air filter
            3.1.2.1.9. A cover of a head of the block of cylinders
            3.1.2.1.10. A camshaft
            3.1.2.1.11. Removal and installation of a head of the block of cylinders
            3.1.2.1.12. Dismantling, repair and assemblage of a head of the block of cylinders
          3.1.2.2. Engine removal
         3.1.2.3. Engine installation
         3.1.2.4. Engine dismantling
          3.1.2.5. Engine assemblage
         3.1.2.6. Start of the engine after major repairs
    3.2. Diesel engines
    3.3. The petrol engine 1,4 дм3
    3.4. Ignition system
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment


3.1.2.1.7. A privodnoj belt of the generator Installation of the belt which was in the use
PERFORMANCE ORDER
1. To remove a pulley of a cranked shaft.
2. To establish plastic a casing: the bottom right, top, bottom left.
3. To establish the adaptation of blocking of a flywheel (Facom D 86) and to tighten a bolt of fastening of a pulley of a cranked shaft the moment of 110 Nanometers.
4. To take the adaptation of blocking of a flywheel.
5. To establish the bottom sheet closing картер couplings.
6. To establish a lateral casing.
7. To establish driving a belt of the generator and to pull it with effort 600 Н (60 kg), if it new, or with effort 400 Н (40 kg) if it was earlier in the use. It is necessary to take advantage of control adaptation Krikit or similar.

Installation of a new belt
PERFORMANCE ORDER
1. To establish the adaptation of blocking of a flywheel (Facom D 86) and to tighten a bolt of fastening of a pulley of a cranked shaft the moment of 110 Nanometers.
2. To take the adaptation of blocking of a flywheel.
3. To establish the top casing of a belt.
4. To establish and pull driving a generator belt.
5. To start the engine which should work before fan inclusion, and then wait, while it will cool down (at least, two hours at an open cowl).
6. To establish the piston of the cylinder 1 in ВМТ. The sign on a flywheel should be opposite to a sign "0" on an adjusting plate of ignition, and the aperture for a core in a pulley should be in the position corresponding to two hours on a dial of hours.
7. To weaken and tighten nuts of the holder of a tension roller and a counternut of the clown.
8. To establish the adaptation of blocking of a flywheel.
9. To remove driving a generator belt.
10. To establish plastic a casing: the bottom right, top, bottom left.
11. To establish a pulley and to tighten bolts the moment of 110 Nanometers.
12. To take the adaptation of blocking of a flywheel.
13. To establish the bottom sheet closing картер couplings.
14. To establish and pull driving a generator belt.
15. To establish a lateral casing.