Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment
   14.1. A technical characteristics
   14.2. Detection of not closed chain
   14.3. The generator
   14.4. A starter
   14.5. Replacement of switches
   14.6. Other electric devices
   14.7. Bulbs of external illumination
   14.8. Bulbs of internal illumination
   14.9. External lighting devices
   14.10. Adjustment of light of headlights
   14.11. A combination of devices
   14.12. Elements of a combination of devices
   14.13. Hours
   14.14. Screen wiper levers
   14.15. The screen wiper and draught engine
   14.16. The engine of a screen wiper of a back door
   14.17. Washers
   14.18. A radio receiver
   14.19. Loudspeakers
   14.20. The aerial
   14.21. Anticreeping system
   14.22. A safety pillow
   14.23. Elements of a pillow of safety
   14.24. Heating and ventilation system
    14.25. Electroschemes and diagrammes





14.9. External lighting devices
THE GENERAL DATA

The prevention

To disconnect a negative wire from the accumulator before removal of any lighting device and repeatedly to connect a negative wire to the accumulator after installation of the lighting device.


HEADLIGHT
The prevention

Before removal of optical knots of headlights it is necessary to designate on a wall (for example, in underground garage) a light trace from headlights of near and far light, and also position of all four wheels.


Removal

PERFORMANCE ORDER
1. Working in a motor compartment, to release bracket, крепящую a cover to a back part of a headlight.
2. To disconnect wires from lamps накаливания, located in a headlight.
3. Working in a motor compartment, to disconnect fixing spring of a lamp of the forward index of turn from a ledge.
4. To take the forward index of turns from a wing.
5. On models with the proof-reader of light of headlights to disconnect the proof-reader from a headlight as follows.
6. To take the case of the proof-reader from a suspension bracket on the forward panel.
7. To take spherical шарнирное connection from a nest in a back part of a headlight.
8. On models with электрически the operated proof-reader of light of headlights to disconnect wires from the proof-reader in a back part of a headlight.
9. To remove a radiator lattice.
10. To unhook a lath located under a headlight, paying attention not to damage fastening about a wing edge.
11. To unscrew two (are specified by an arrow) an external bolt of fastening of a headlight and to take a headlight forward from the body panel.
12. To remove metal clips of fastening of glass to a headlight and to remove glass from a headlight.
13. Before installation of glass of a headlight to check up that the consolidation located in a flute on perimetre of a headlight, in a good condition.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.
2. As soon as possible to adjust light of headlights.

THE FORWARD INDEX OF TURN

PERFORMANCE ORDER
1. Working in a motor compartment, to disconnect fixing spring of a lamp of the forward index of turn from a ledge.
2. To take the forward index of turns from a wing.

THE FORWARD LATERAL REPEATER OF TURNS

PERFORMANCE ORDER
To turn the forward lateral repeater of turns counter-clockwise and to take it from a car wing.

FORWARD ANTIFOG HEADLIGHTS

Two kinds of headlights can be established. Headlights can be established or is direct in a forward spoiler, or in a nest screwed on a forward spoiler.

PERFORMANCE ORDER
The antifog headlight established in a nest of a spoiler
1. In a back part of a spoiler to disconnect an electric socket from a headlight.
2. To unscrew two screws (fastenings of an antifog headlight to a spoiler are specified by an arrow) then to take a headlight with a nest from a spoiler.
3. To unscrew a nut (it is specified by an arrow) fastenings in a back part of a headlight and to take a headlight from a nest.
4. Installation is made in sequence, return to removal.
5. To check up and if it is necessary to adjust light of headlights, using nuts with накаткой in a back part of a headlight.
The headlight established directly in a spoiler

The prevention

Some models are equipped by forward antifog headlights which have no screws of fastening, visible has from outside flown down headlights.


6. To lift a forward part of the car and to fix on supports.
7. To track electroconducting back from an antifog headlight and to disconnect an electric socket.
8. To unscrew nuts of fastening and to take a headlight from a spoiler.
9. Installation is made in sequence, return to removal.

BACK LANTERN (MODELS THE SEDAN)

PERFORMANCE ORDER
1. To open a luggage carrier cover.
2. To compress two brackets fastenings and to take the holder of bulbs from a back lantern.
3. To disconnect an electric socket from the holder of bulbs.
4. To remove luggage space furnish.
5. To unscrew nuts (are specified by arrows) fastenings of a back lantern.
6. To remove a back lantern, thus it is necessary to take an external part of a lantern at first.
7. Installation is made in sequence, return to removal.

BACK LANTERN (MODEL КОМБИ)

Fires of a stoplight and the turn index are located in a back wing. Other bulbs of a back lantern are located in a back door.

PERFORMANCE ORDER
1. To open a back door.
2. To turn bracket fastenings and to open a folding shutter of a covering of a luggage space.
3. To compress two brackets fastenings and to take the holder of bulbs from a back lantern.
4. To disconnect an electric socket from the holder of bulbs.
5. To unscrew nuts (are specified by arrows) fastenings of a back lantern.
6. To unscrew nuts (are specified by arrows) fastenings of a back lantern to a door.
7. To remove a back lantern.
8. Installation is made in sequence, return to removal.

LICENSE PLATE ILLUMINATION (MODELS THE SEDAN)

PERFORMANCE ORDER
1. To unscrew two screws (fastenings are specified by arrows) then to take a lantern of illumination from a bumper and to disconnect an electric socket.
2. Installation is made in sequence, return to removal.

LICENSE PLATE ILLUMINATION (MODEL КОМБИ)

PERFORMANCE ORDER
1. By means of the lever to remove a lantern of illumination of licence plate from a back door and to disconnect an electric socket.
2. Installation is made in sequence, return to removal.