Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment
   14.1. A technical characteristics
   14.2. Detection of not closed chain
   14.3. The generator
   14.4. A starter
   14.5. Replacement of switches
   14.6. Other electric devices
   14.7. Bulbs of external illumination
   14.8. Bulbs of internal illumination
   14.9. External lighting devices
   14.10. Adjustment of light of headlights
   14.11. A combination of devices
   14.12. Elements of a combination of devices
   14.13. Hours
   14.14. Screen wiper levers
   14.15. The screen wiper and draught engine
   14.16. The engine of a screen wiper of a back door
   14.17. Washers
   14.18. A radio receiver
   14.19. Loudspeakers
   14.20. The aerial
   14.21. Anticreeping system
   14.22. A safety pillow
   14.23. Elements of a pillow of safety
   14.24. Heating and ventilation system
    14.25. Electroschemes and diagrammes





14.7. Bulbs of external illumination
THE GENERAL DATA

The prevention

Before replacement of bulbs of external illumination to check up a corresponding electric chain and a safety lock.

Do not concern a glass flask of a lamp with hands. The fingerprint evaporates and besieged on a reflector therefore illumination worsens. It is obligatory to replace the failed lamps with lamps of the same type. Stains arising on imprudence from a touch to wipe pure безворсовой a rag or spirit.


HEADLIGHT

PERFORMANCE ORDER
1. To release brackets (fastenings are specified by an arrow) and to uncover a back part of a headlight.
2. To remove an electric socket from a back part of a lamp накаливания headlights.
3. To compress spring brackets (fastenings of a bulb are specified by an arrow) and to cast away them aside.
4. To take a bulb from a headlight.
5. To establish a new bulb so that ledges on a bulb cartridge were combined with headlight grooves, and to fix a bulb spring bracket.
6. To connect an electric socket and to establish a back cover of a headlight.

FORWARD DIMENSIONAL LANTERN

The lamp накаливания a dimensional lantern is located in a back part of a headlight.

PERFORMANCE ORDER
1. To release bracket fastenings and to remove a back cover from a headlight.
2. On models till 1992 to take a cartridge with a bulb from a back part of a headlight. On models since 1993 to turn a cartridge with a bulb on a quarter of a turn and to take a cartridge with a bulb from a back part of a headlight.
3. To take a lamp накаливания from a cartridge, simply having pulled it on itself.
4. Installation is made in sequence, return to removal.

THE FORWARD INDEX OF TURN

PERFORMANCE ORDER
1. Working in a motor compartment, to disconnect fixing spring (it is specified by an arrow) lamps of the forward index of turn from a ledge.
2. To take the forward index of turns from a wing.
3. To turn a cartridge counter-clockwise to take it from the forward index of turns.
4. To take a lamp накаливания from a cartridge, simply having pulled it on itself.
5. Installation is made in sequence, return to removal, thus to check up that the fixing spring is correctly established.

THE FORWARD LATERAL REPEATER OF TURNS

PERFORMANCE ORDER
1. To turn the forward lateral repeater of turns counter-clockwise and to take it from a car wing.
2. To turn a cartridge with a bulb counter-clockwise and to take it from the forward lateral repeater of turns.
3. To take a lamp накаливания from a cartridge, simply having pulled it on itself.
4. Installation is made in sequence, return to removal.

ADDITIONAL FORWARD LIGHT

On some models additional forward light is established in a headlight. Additional forward light joins at headlight inclusion.

Bulb replacement is made the same as also headlight bulbs (see above).

PERFORMANCE ORDER
1. To release spring brackets (are specified by an arrow) fastenings of a bulb of additional forward light.
2. To take a bulb of additional forward light from a headlight.

FORWARD ANTIFOG HEADLIGHTS


The prevention

Some models are equipped by forward antifog headlights which have no screws of fastening visible from outside headlight glass.


Two kinds of headlights can be established. On some models access to a lamp накаливания can be possible from a back part of a spoiler. On other models for access to a bulb it is necessary to remove a headlight.

PERFORMANCE ORDER
1. On models where access to a lamp накаливания is possible from a back part of a spoiler to disconnect an electric socket from a bulb.
2. To remove a rubber cover from a headlight, then to compress spring clamps and to take a bulb.
3. On models where the back part of an antifog headlight is closed by a spoiler to unscrew two screws of fastening from a forward part of a headlight and to take a headlight from a spoiler.
4. To disconnect an electric socket from a bulb, then to compress spring clamps and to take a bulb.

BACK LANTERN (MODELS THE SEDAN)

PERFORMANCE ORDER
1. To open a luggage carrier cover.
2. To compress two brackets fastenings and to take the holder of bulbs from a back lantern.
3. For bulb extraction to press it, in this position to turn in any party and to take from the holder.
4. Installation is made in sequence, return to removal.

BACK LANTERN (MODEL КОМБИ)

Fires of a stoplight and the turn index are located in a back wing. Other bulbs of a back lantern are located in a back door.

PERFORMANCE ORDER
1. To open a back door.
2. To turn bracket fastenings and to open a folding shutter of a covering of a luggage space.
3. To compress two brackets fastenings and to take the holder of bulbs from a back lantern.
4. For bulb extraction to press it, in this position to turn in any party and to take from the holder.
5. Installation is made in sequence, return to removal.

LICENSE PLATE ILLUMINATION (MODELS THE SEDAN)

PERFORMANCE ORDER
1. Using a thin screw-driver, to remove a plafond from an underside of a bumper for access to a lamp накаливания.
2. For bulb extraction to press it, in this position to turn in any party and to take from the holder.
3. Installation is made in sequence, return to removal.

LICENSE PLATE ILLUMINATION (MODEL КОМБИ)

PERFORMANCE ORDER
1. Using a thin screw-driver, to remove a lantern of illumination of licence plate from a back door.
2. To take a cartridge with a bulb from a lantern.
3. For bulb extraction to press it, in this position to turn in any party and to take from the holder.
4. Installation is made in sequence, return to removal.