14.5. Replacement of switches

MULTIPURPOSE SWITCHES OF THE STEERING COLUMN (MODEL TILL 1993)

PERFORMANCE ORDER

1. To remove casings of a steering column. 2. To unscrew two screws (are specified by arrows) switch fastenings to an arm of a steering column. 3. To remove the switch and to disconnect an electric socket. 4. Installation is made in sequence, return to removal.

MULTIPURPOSE SWITCHES OF THE STEERING COLUMN (MODEL SINCE 1993)

PERFORMANCE ORDER

1. Switch removal is made is similar earlier stated (see above). Difference consists that access to screws (are specified by an arrow) switch fastenings is carried out from a forward part of the switch. 2. To remove the multipurpose switch from a steering column.

SWITCHES ON THE PANEL OF DEVICES (MODEL TILL 1992)

PERFORMANCE ORDER

1. Using a thin screw-driver, to release the plastic clamps located on each side of the switch and to take the switch from the panel of devices. 2. To disconnect from the switch an electric socket. 3. At installation to connect to the switch an electric socket and to press the switch into a nest in panels before fixing by its clamps.

SWITCHES ON THE PANEL OF DEVICES (MODEL SINCE 1993)

PERFORMANCE ORDER

1. Switch removal is made is similar earlier stated (see above) except that plastic clamps are located from above and from below the switch. 2. To remove the switch from the panel of devices.

THE SWITCH OF THE FAN OF THE HEATER

The switch compound with the control panel a heater also cannot separately be replaced from the panel.

SWITCHES ON THE CENTRAL CONSOLE

Forward switches

PERFORMANCE ORDER

1. Using a thin screw-driver, to remove decorative furnish of the basis under the lever of a manual brake. 2. Using a thin screw-driver, to remove switch furnish. 3. Using a thin screw-driver, to remove the switch from the central console and to disconnect an electric socket. 4. Installation is made in sequence, return to removal.

Back switches

PERFORMANCE ORDER

1. Using a thin screw-driver, to remove a back ashtray from the central console. 2. Using a thin screw-driver, to remove switch furnish. 3. Using a thin screw-driver, to remove the switch from the central console and to disconnect an electric socket. 4. Installation is made in sequence, return to removal.

SWITCHES ON THE DOOR

PERFORMANCE ORDER

1. By means of a thin screw-driver to take the switch from a nest on a door of the car and to disconnect an electric socket. 2. Installation is made in sequence, return to removal.

SWITCHES OF ILLUMINATION OF SALON

The switch on a door rack

PERFORMANCE ORDER

1. To open a door, then to remove a rubber protective cover (it is specified by an arrow) from the switch. 2. To unscrew the screw of fastening and to take the switch from a door rack. 3. To disconnect an electric socket from the switch and to adhere to the switch a thin cord that the wire from the switch has not failed in a door rack. 4. Installation is made in sequence, return to removal.

The switches established on a ceiling

Switches compound with lanterns also cannot be replaced separately.

The switch of illumination of a luggage carrier (model the Sedan)

The switch is located in a suspension bracket and copes the hinge of a cover of a luggage carrier.

PERFORMANCE ORDER

1. To open a luggage carrier cover. 2. To release brackets and to take the switch from a suspension bracket. 3. To disconnect an electric socket and to remove the switch. 4. Installation is made in sequence, return to removal.

The switch of illumination of a luggage carrier (model of Kombi)

Luggage space illumination copes the switch sensitive to an inclination and located in a back door.

PERFORMANCE ORDER

1. To open a back door. 2. To unscrew screws and to remove plastic furnish from an internal part of a back door. 3. Working on perimetre of carpet furnish of a back door, to release brackets fastenings and to remove carpet furnish of a back door. 4. To unscrew the screw (it is specified by an arrow), securing the the switch to a back door. 5. To disconnect an electric socket and to remove the switch. 6. Installation is made in sequence, return to removal.

THE SWITCH OF THE HATCH WITH THE ELECTRIC DRIVE

PERFORMANCE ORDER

1. Using a thin screw-driver, to remove locking plate (close to the hatch switch) from the top console. 2. Through an aperture formed after removal of the locking plate to push out the switch and to disconnect an electric socket. 3. Installation is made in sequence, return to removal.