Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
    11.1. A forward suspension bracket
    11.2. A back suspension bracket
      11.2.1. A technical characteristics
      11.2.2. Shock-absorber replacement
      11.2.3. Replacement torsionов
      11.2.4. The stabilizer
      11.2.5. The suspension bracket lever
      11.2.6. Removal and installation of a back suspension bracket
      11.2.7. Adjustment of height of a suspension bracket of a body
      11.2.8. Naves of back wheels
      11.2.9. Features of a back suspension bracket of cars 4 х 4
      11.2.10. Tank replacement
      11.2.11. Removal and installation of the lever of a suspension bracket
      11.2.12. Removal and installation of the cylinder of a suspension bracket
      11.2.13. Removal of air from a hydraulic contour
      11.2.14. Removal and pump installation
      11.2.15. Removal and nave installation
12. Brake system
13. A body
14. An electric equipment


11.2.6. Removal and installation of a back suspension bracket
THE GENERAL DATA
The prevention

The back suspension bracket is attached to a body by bolts Torx. Long tip Torx is necessary For removal of a back suspension bracket №50.

Knot of a back suspension bracket


Removal of knot of a back suspension bracket

1 – a bulk pipe,
2 – fastening of a tank,
3 – a pipe of an exhaust system,		 4 – a cable of a manual brake,
5 – подпора beams

Removal of knot of a back suspension bracket

1 – the holder of a beam,

2 – fastening on металлорезиновом an element,

3 – fastening to a body

Removal

PERFORMANCE ORDER
1. To lift the car and to establish it on supports.
2. To remove a back part of an exhaust system to a forward pipe.
3. To merge fuel from a tank.
4. To remove a holder of fastening of a bulk pipe. To separate a pipe from a tank.
5. To remove the bottom casing (equipment of some versions) and the heat-shielding screen.
6. To disconnect from a body the holder of a connector of cables of a manual brake.
7. From below bodies to remove draught of a manual brake.
8. To remove a cable of a manual brake.
9. To weaken, without вывинчивания, two bolts of back fastening to a fuel tank.
10. In the version with drum-type brakes to disconnect from above each lever of a suspension bracket, and in the version with disk brakes – on the left side, the union of connection of a brake hose. To muffle corresponding connections of brake system.
11. In disk brakes to disconnect tubes from the terminator and to close apertures.
12. To establish a jack under a beam pipe.
13. To weaken bolts of fastening of back holders of a beam to a body and to unscrew them.
14. To unscrew bolts of forward holders.
15. A few to lower a jack and to move back all knot of a back suspension bracket for extraction of a bulk tube from a fuel tank.
16. To lift a body.
17. To take all knot of a back suspension bracket.

Installation

PERFORMANCE ORDER
1. To place knot of a back suspension bracket under a body, опирая a beam on a jack.
2. To lower a body more low and to place knot of a back suspension bracket on a corresponding place.
3. To screw up bolts of fastening of forward holders of a beam to a body (it is necessary to use a tip of Torx №50).
4. To screw up bolts of fastening of back holders of a beam to a body.
5. To connect connections of brake system.
6. To screw up bolts of fastening of a tank.
7. To establish a cable of a manual brake.
8. To establish draught of a manual brake.
9. To establish on a body the holder of a connector of cables of a manual brake.
10. To establish the heat-shielding screen of an exhaust system.
11. To adjust a bulk pipe to a tank and to fix its new holder of fastening.