Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
    11.1. A forward suspension bracket
    11.2. A back suspension bracket
      11.2.1. A technical characteristics
      11.2.2. Shock-absorber replacement
      11.2.3. Replacement torsionов
      11.2.4. The stabilizer
      11.2.5. The suspension bracket lever
      11.2.6. Removal and installation of a back suspension bracket
      11.2.7. Adjustment of height of a suspension bracket of a body
      11.2.8. Naves of back wheels
      11.2.9. Features of a back suspension bracket of cars 4 х 4
      11.2.10. Tank replacement
      11.2.11. Removal and installation of the lever of a suspension bracket
      11.2.12. Removal and installation of the cylinder of a suspension bracket
      11.2.13. Removal of air from a hydraulic contour
      11.2.14. Removal and pump installation
      11.2.15. Removal and nave installation
12. Brake system
13. A body
14. An electric equipment


11.2.3. Replacement torsionов
THE GENERAL DATA

Fastening torsionа on the lever

1 – the lever,

2 – a fastening bolt torsionа,

3 – eccentric a blocking lining,

4 – a bolt of fastening of the stabilizer,

5 – a bolt of face fastening of the stabilizer,

6 – a basic lining

Removal

PERFORMANCE ORDER
1. To establish the car on the lift and to remove shock-absorbers, and also the stabilizer.
2. To establish the car on supports.
3. On a shock-absorber place to establish the adaptation 7.0908 V (to adjust its length so that it was possible to place freely an axis in the lever).
4. To screw up an adaptation counternut.
5. On an opposite side, at an end face torsionа to unscrew a bolt and to remove a lining.
6. On the party from which acts in film torsion to unscrew a bolt and to remove a basic lining.
7. To designate position torsionа two blows кернера (on torsionе and the lever).
8. To establish a tip 7.0908 Q (a shaft improved with carving М8х125) on the end torsionа, and on a tip – an inertial stripper (8.0316).
9. To remove torsion (it is necessary to look that the lever has not moved back together with torsionом).

Installation

PERFORMANCE ORDER
1. It is necessary to adjust distance of an axis of the adaptation 7.0908 V:
      – To recommended value, if torsion the new;
      – To the value defined for correction of height of a suspension bracket of a body;
      – To the value measured during removal.
The prevention

In an installation time it is not necessary to interchange the position torsionы:
      – torsion the right: 1 sign executed by a paint;
      – torsion the left: 2 signs executed by a paint.

2. On a shock-absorber place to establish the special adjusted adaptation.
3. To establish on torsion from outside the lever a tip, and also an inertial stripper (0908 Q).
4. To check up, whether are well cleared Slots, and then to grease with their greasing Esso Norva 275.
5. On an opposite side from the party from which it is removed torsion to establish a basic lining in a nest.
6. To establish torsion through a fastening element in the lever, and then, turning it, to find position in which torsion freely will enter on depth of 8-10 mm.
The prevention

Торсион freely enters only on 8–10 mm.

7. To finish installation torsionа by means of a stripper when it will rest against a basic lining.
8. To remove a tip and a stripper.
9. To fill a nest with greasing.
10. To establish a basic lining and to tighten each end torsionа the moment of 17,5 Nanometers.
11. To screw up two bolts of the holder of a cable of a manual brake.
12. To remove the adaptation established on a place of the shock-absorber.
13. To establish the shock-absorber.
14. To establish the stabilizer.
15. To establish the car on wheels.
16. To check up height of a suspension bracket of a body and in case of need to correct.