Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
   10.1. A technical characteristics
   10.2. A steering wheel
   10.3. A steering column
   10.4. The ignition lock
   10.5. Steering transfer
   10.6. Replacement of protective covers of the steering mechanism
   10.7. Removal of air from system of a steering with the amplifier
   10.8. The pump of the amplifier of a steering
   10.9. Check of level of oil in system of a steering with the hydraulic booster
   10.10. A tip of steering draught
   10.11. Steering draught
   10.12. Corners of installation of wheels
   10.13. Changes in steering system
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment





10.5. Steering transfer
THE GENERAL DATA

Arrangement of elements of system of a steering with the hydraulic booster

1 – pipelines,

2 – pipelines of the servomotor,

3 – the dividing valve,

4 – steering transfer,

5 – the servomotor

Fastening of steering transfer on a cross-beam

1 – bolts of fastening,

2 – nuts,

3 – steering transfer,

4 – the holder of an intermediate element of management of a transmission

Elements of system of a steering without the hydraulic booster

1 – картер steering transfer,
2 – the bearing,
3 – a restrictive ring,
4 – a cover,
5 – рейка,
6 – the bearing driving gear wheels,
7 – a ring,
8 – приводная a gear wheel,
9 – an emphasis рейки,
10 – a spring of an emphasis,
11 – adjusting washers,
12 – a cover,
13 – an elastic cover,
14 – a basic lining of the axial spherical hinge,
15 – a restrictive lining of the axial spherical hinge,
16 – the axial spherical hinge of steering draught,
17 – steering draught,
18 – the spherical hinge,
19 – a casing of the spherical hinge

Elements of system of a steering with the hydraulic booster

1 – картер steering transfer,
2 – the bearing,
3 – a restrictive ring,
4 – the bearing driving gear wheels,
5 – knot a gear wheel-dividing the valve,
6 – an emphasis рейки,
7 – a spring of an emphasis,
8 – adjusting washers,
9 – a cover,
10 – рейка,
11 – the spherical hinge,
12 – steering draught,
13 – the axial spherical hinge of steering draught,
14 – a restrictive lining of the axial spherical hinge,
15 – the servomotor hydraulic,
16 – hydraulic hoses,
17 – the pump,
18 – a pulley of the pump,
19 – an oil tank

Removal

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To lift a forward part of the car and to fix on supports. To remove forward wheels.
3. On models with a steering drive with the hydraulic booster to merge a hydrosystem liquid as follows:
      – To uncover a nutritious tank;
      – To place the container under муфтой the high pressure pipeline on steering transfer, then to unscrew connection;
      – To merge a liquid in the container;
      – To finish plums of oil from a contour, turning some times a steering wheel in both directions against the stop;
      – To disconnect a hose of low pressure from steering transfer.
4. At presence to unscrew a bolt from a heat resisting guard of steering transfer.
5. On models a mechanical transmission to disconnect from steering transfer a bolt of an intermediate element of a transmission.
6. To put combination labels between the end of an intermediate shaft and a gear wheel of steering transfer, then to unscrew tightening a bolt, securing the the universal hinge of an intermediate shaft to a gear wheel.
7. Working on one party of the car, to weaken, and partially to unscrew a nut of the spherical hinge from the end of steering draught and using a stripper to remove the spherical hinge and definitively to unscrew a nut.
8. To repeat procedure on other party of the car.
9. To unscrew two bolts of fastening of steering transfer to a cross-beam.
10. To turn steering transfer round a horizontal axis so that the gear wheel was in the basis, then to take steering transfer from under the right arch of a wheel.

Repair

PERFORMANCE ORDER
1. To check up the steering mechanism on deterioration and damages.
2. To check up that gear рейка moves freely for all length of a course.
3. To check up backlash between a gear wheel of the steering mechanism and gear rack.
4. To check up all hydraulic connections on leak.

THAT is necessary to make repair of the steering mechanism at station.

It is independently possible to make only replacement of protective covers of the steering mechanism, spherical hinges of steering draughts and steering draughts.

Installation

PERFORMANCE ORDER
1. To establish the steering mechanism into place, having combined a gear wheel of the steering mechanism with intermediate shaft with the account before the made labels.
2. To insert linings between the bottom frame and the steering mechanism. To insert bolts of fastening of the steering mechanism and to tighten their demanded moment.
3. To connect pipes of the amplifier of a steering and to tighten connecting nuts the demanded moment.
4. To establish tightening a bolt of an intermediate shaft and a new nut. To tighten their demanded moment.
5. To establish spherical hinges of steering draught in rotary fists and to fix their new nuts.
6. To connect an electric socket and the thermal screen to the steering mechanism. To establish wheels and to lower the car.
7. To add a liquid in a tank and to remove air from hydraulic system. To remove air from a contour, some times turning a steering wheel from an emphasis against the stop. To add quantity of oil in process of fall of its level.
8. To check up and if necessary to adjust corners of installation of wheels.