Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
4.1. Fuel system with the carburettor
4.2. One-dot systems of injection of fuel
4.2.1. Pressure removal in fuel system
4.2.2. Adjustment of a cable of an accelerator
4.2.3. The fuel pump
4.2.4. An injector
4.2.5. Check of system of injection of fuel
4.2.6. Elements of system of injection Fenix
4.2.7. Elements of system of injection Bosch Monopoint
4.2.8. Elements of system of injection Magneti Marelli
4.3. Multidot systems of injection of fuel
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment
|
FUEL ATOMIZER
Removal and installation
| PERFORMANCE ORDER |
| 1. To remove the gauge of temperature of air. |
|
2. Unscrew накидную a nut of a fuel atomizer. |
|
3. To remove a fuel atomizer and the bottom ring consolidation. |
|
4. At atomizer installation it is necessary that consolidation of round section and an atomizer head were in a good condition. At correct installation of a head of an atomizer atomizer pins (are specified by arrows) will join head clips that is noted "" and "-" for identification. |
|
FUEL REGULATOR OF PRESSURE
Removal
| PERFORMANCE ORDER |
| 1. To remove pressure in fuel system. |
| 2. To remove a wire of weight from the accumulator. |
| 3. To uncover the air filter. |
| 4. To remove a spring and a diaphragm, marking their orientation. |
|
5. To remove a regulator casing, preliminary having noted its arrangement (screws of fastening of a regulator of pressure are specified by arrows). |
|
THE ENGINE OF MANAGEMENT OF THE IDLING MODE
Removal
| PERFORMANCE ORDER |
| 1. To remove a wire of weight from the accumulator. |
| 2. To remove bracket and to disconnect a socket from the engine. |
|
3. To unscrew screws (are specified by arrows) and to remove the engine of management of an idling mode. |
|
POTENTIOMETER OF POSITION THROTTLE ЗАСЛОНКИ
The potentiometer of position throttle заслонки is not folding knot and at failure is subject to replacement.
THE GAUGE OF TEMPERATURE OF ARRIVING AIR
The gauge of temperature of arriving air, integral part of a head of an injector.
Removal
| PERFORMANCE ORDER |
| 1. To remove a wire of weight from the accumulator. |
| 2. To remove the air filter. |
|
3. To unscrew three screws (are specified by arrows) fastenings of a plastic ring. |
|
4. To remove ring consolidation from a plastic ring. |
| 5. To wring out bracket and to remove a socket from an injector. |
|
6. To unscrew a bolt of fastening of a head of an injector (it is specified by an arrow) and to remove it together with condensing ring. |
|
THE ELECTRONIC CONTROL DEVICE (ECU)
ECU it is located in a plastic box which is established behind the accumulator.
Removal
| PERFORMANCE ORDER |
| 1. To disconnect the accumulator. |
| 2. To remove a casing from a box, then to wring out bracket and to disconnect a socket. |
| 3. To unscrew a nut and to remove the relay from back part ECU of a box. |
| 4. To unscrew screws and to remove ECU a box from a storage platform. |
|
THE RELAY OF SYSTEM OF INJECTION OF FUEL
The relay is established behind ECU a plastic box which is located directly behind the accumulator.
THE GAUGE OF POSITION OF THE CRANKED SHAFT
The gauge of a cranked shaft is located on a face sheet картера transmissions.
Removal
| PERFORMANCE ORDER |
| 1. To disconnect a wire of weight from the accumulator. |
| 2. To track electroconducting from the gauge to an electroconducting connector, and to disconnect it from the main plait. |
| 3. To unscrew a bolt of fastening and by means of the lever to take the gauge from a rubber condensing ring. |
|
THE GAUGE OF SPEED
The gauge of speed of the car – an integral part of a drive of a speedometer. |
|