Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
7. Coupling
8. Transmissions
9. Power shafts
9.1. A technical characteristics
9.2. Removal of power shafts
9.3. Power shaft installation
9.4. Replacement of covers of hinges of equal angular speeds
9.5. Replacement of the intermediate bearing of the right power shaft
9.6. A drive on forward wheels with the power unit 4 х 4
9.7. A drive on back wheels with the power unit 4 х 4
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment
|
The prevention At installation spherical swivel connections of the bottom lever it is necessary to use a new nut.
Blocking of a nave by means of plugs 0606 AY
| PERFORMANCE ORDER |
| 1. The car should stand on wheels. On the corresponding party it is necessary to unscrew a bolt of fastening of a connector of the stabilizer with the suspension bracket lever. |
|
|
| 2. To remove a cap of a nave of a wheel and to remove R-shaped bracket (drawing at the left) and a head (drawing on the right) blockings of a nut of fastening of a power shaft to a nave. To weaken a nut of fastening of a power shaft to a nave on the car, standing wheels on the earth. Also to weaken bolts of fastening of a wheel. To lift a forward part of the car and to fix on supports. To remove a corresponding forward wheel. |
| 3. To remove the bottom casing (equipment in some versions). |
| 4. To merge oil from a transmission. |
| 5. On the models equipped ABS to remove the gauge established on a wheel of the car. |
| 6. To unscrew a nut of fastening of a power shaft to a nave. |
The prevention For simplification of unscrewing of a nut of a nave it is necessary to use the plugs blocking a nave (fig. Blocking of a nave by means of plugs 0606 AY see). At all it is not necessary to press a brake pedal, it can cause cutting of bolts of fastening of a brake disk.
|
|
7. To unscrew a nut of the spherical hinge of a suspension bracket. To take the spherical hinge from the lever by means of a universal stripper for spherical hinges. |
|
THE LEFT POWER SHAFT
| PERFORMANCE ORDER |
| 1. To take away a nave from the car and to take the external end of a power shaft from a nave. If necessary for extraction of a shaft from a nave to use a rubber hammer or киянку. |
| 2. Supporting a power shaft, to take the internal end of a shaft from a transmission, trying not to damage a sealing ring of differential thus. To take a power shaft from under the car. |
The prevention In no event it is impossible to lower the car on wheels with the removed one or two power shafts since it will lead to damage of bearings of a wheel. If it is necessary to move the car, it is necessary to establish temporarily the external end of a power shaft in a nave and to fix its nut.
|
|
THE RIGHT POWER SHAFT
| PERFORMANCE ORDER |
|
1. To weaken two bolts of fastening of the intermediate bearing. |
|
2. Then to turn bolts (are specified by arrows) on 90 ° so that their heads were displaced from the external end of the bearing. |
| 3. To take away a nave from the car and to take the external end of a power shaft from a nave. If necessary, for extraction of a shaft from a nave to use a rubber hammer or киянку. |
| 4. Supporting the external end of a power shaft, to take the internal end of a shaft from a transmission and to release the intermediate bearing from an installation suspension bracket. |
5. After extraction of a power shaft from a transmission to remove a protective cover from the internal end of a shaft, marking a place of its installation and to take a power shaft from under the car.
The prevention In no event it is impossible to lower the car on wheels with the removed one or two power shafts since it will lead to damage of bearings of a wheel. If it is necessary to move the car, it is necessary to establish temporarily the external end of a power shaft in a nave and to fix its nut.
|
|
|
|