Peugeot405
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Fuel system
5. Systems of greasing, cooling
6. Release system
   6.1. Removal and installation
   6.2. System of fall of toxicity of an exhaust
   6.3. The issue control картерных gases
   6.4. The control of the fulfilled gases
   6.5. The control of allocation of steams of fuel
   6.6. System of fall of toxicity of an exhaust
   6.7. The catalyst
7. Coupling
8. Transmissions
9. Power shafts
10. A steering
11. Suspension brackets
12. Brake system
13. A body
14. An electric equipment





6.1. Removal and installation
THE GENERAL DATA

Each section of system of release can be removed individually or the full system can be removed as unit. Even if only one part of system requires service or replacement, often it is easier to remove the whole system and to separate demanded section in garage.

Removal

PERFORMANCE ORDER
For removal of system of release or a system part it is necessary to lift a forward or back part of the car and to fix on supports or to establish the car on a viewing hole.

FORWARD PIPE

PERFORMANCE ORDER
1. To unscrew nuts of fastening of a reception exhaust pipe to a final collector, then to unscrew a bolt, securing the a reception exhaust pipe to an installation suspension bracket.
2. To disconnect a reception exhaust pipe from a collector and to remove a lining.
3. To unscrew nuts of fastening of a flange of a back part of a reception exhaust pipe, to remove a pipe and to take from under the car.

FORWARD EXHAUST PIPE

PERFORMANCE ORDER
To unscrew nuts of fastening of flanges of a forward and back part of a forward exhaust pipe, to remove a pipe and to take from under the car.

INTERMEDIATE EXHAUST PIPE

PERFORMANCE ORDER
To unscrew nuts of fastening of flanges of a forward and back part of an intermediate exhaust pipe, to remove a pipe and to take from under the car.

THE CENTRAL MUFFLER

PERFORMANCE ORDER
1. To weaken bolts of a coupling ring and to disconnect clips from forward and back фланцевых connections.
2. To disconnect the central muffler from rubber pillows and to take from under the car.

EXHAUST PIPE AND THE MUFFLER

PERFORMANCE ORDER
1. To weaken bolts of a coupling ring of an exhaust pipe and to disconnect a clip from фланцевого connections.
2. To disconnect an exhaust pipe from rubber pillows and to take from under the car.

FULL EXHAUST SYSTEM

PERFORMANCE ORDER
1. To unscrew nuts of fastening of a reception exhaust pipe to a final collector, then to unscrew a bolt, securing the a reception exhaust pipe to an installation suspension bracket.
2. To disconnect a reception exhaust pipe from a collector and to remove a lining.
3. To release an exhaust system from rubber pillows and to take from under the car.

HEAT RESISTING GUARDS

Arrangement of a heat resisting guard on an underside of a fuel tank

Heat resisting guards are attached from below the car (and on some models on a fuel tank) by nuts and bolts.

PERFORMANCE ORDER
1. Heat resisting guards can be removed after removal of corresponding section of an exhaust system.
2. If the heat resisting guard leaves, for access to a component located behind a guard, can be sufficient in certain cases to unscrew nuts or bolts and simply to lower a heat resisting guard (without removal of system of release).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal, taking into account following moments.
2. To check up that all traces of corrosion are removed and to replace all linings.
3. To check up rubber pillows on deterioration and damages and, if necessary, to replace.
4. Before assemblage фланцевых connections to grease interfaced surfaces with high-temperature lubricant.
5. To a definitive tightening of connectors of system of release to check up that all rubber pillows are correctly located and that there is a corresponding backlash between the bottom of the car and release system.
6. To move release system to the parties both upwards and downwards and to check up, that the system moved freely, without concerning car knots.